How To Clean Your Vape Tank and Keep It in Good Condition

0
47
vape tank

Vaping is an amazing hobby, and you can spend years exploring how to get the most out of your equipment. However, it’s important to remember that vaping has only really been around for a few years. While vapes are incredibly durable and reliable compared to older devices like e-cigarettes and vape pens, they do require maintenance every once in a while. The following steps suggested by AVS where you can buy vape accessories in Australia will ensure your tank continues working well as well as looking great.

1. Disassemble your tank.

To start the process, you’ll need to disassemble your tank. First, remove the coil and blow out any remaining liquid with a dry paper towel. Next, remove the drip tip and wipe it down with an alcohol-soaked cloth or paper towel. Next, detach the top cap from the base by unscrewing it in a counterclockwise direction while holding on to both pieces of hardware. Set aside until later when you’re ready to clean them both together so as not to mix up their parts accidentally.

Finally, place all of your components in separate bowls filled with warm water and dish soap; rinse each piece thoroughly before setting them out on paper towels or rags for drying overnight (longer if possible).

2. Empty out your tank, and get rid of any remaining liquid.

Once you’ve emptied out your tank, it’s time to get rid of any remaining liquid. A cotton swab (or even a Q-tip) will allow you to reach into the smaller crevices of your tank and clean out any residue that may have escaped from Step 1. If you’re feeling particularly ambitious, this can also be done with a paper towel, though it is more likely that some residue will remain behind for further cleaning in Step 3.

Next up: cleaning around the threads of your vape tank. This is especially important if you’ve been using e-liquids that contain nicotine—as these liquids are known for being sticky and hard to wash off.

3. Cleaning the components that make up the build deck.

The build deck is the part of your vape tank that houses all of the components necessary to make it work. It typically has three parts:

  • The coil and wire, are in charge of heating up the e-juice so that it becomes vaporized into a mist.
  • The posts (sometimes called terminals), are where you connect your coils and wires to.
  • The top cap, which screws onto both ends of the post to seal everything in place and keep any e-juices from leaking out of your tank

To clean this area, you’ll want to remove all four pieces—the top cap, two terminals with posts attached on either side and finally a new coil or some pre-built coils if you have them—and put them in a small bowl filled with warm soapy water for 10 minutes. This will loosen up any residue left over from previous builds or cleaning jobs.

After removing each piece individually from its soak and rinsing thoroughly under running water (or using compressed air), dry off each one with paper towels before reinstalling them back into place on their corresponding posts within the build deck (not forgetting about orientation).

4. Take Your Tank Apart Further, And Start Cleaning

Now that you have your tank opened, you can start cleaning it more thoroughly. It’s time to take apart the tank even further. Take a cotton swab and dip it into some distilled water or vegetable glycerin (available at any grocery store). Then wipe down all of the parts of the vape tank that are hard to reach with your fingers, including:

  • The drip tip
  • The chimney (that part in between where your e-liquid goes)
  • The coil (the part where there is a piece of metal wrapped around something)
  • The tank itself

5. Rinse Your Tank, Let It Dry Thoroughly, And Assemble It Again.

Rinse your tank carefully with cool water to remove any lingering residue. Let it dry thoroughly before reassembling and using it again. Repeat this process monthly or as needed, depending on how often you vape and the materials used in your e-liquid.

Conclusion

Vaping is a great hobby and lifestyle, but it can be frustrating when you’re not able to vape because your tank is dirty. By following these steps you will be able to keep your vape tank in good condition so that it doesn’t break down on you when you need it most.

LEAVE A REPLY

Please enter your comment!
Please enter your name here